What Sizes Are License Plate Screws? FULL LIST

What sizes are license plate screws? The dimensions of license plate screws are very important, because there are different types of fasteners, and using the wrong one can make it easy to lose your license plate.

For example, if you have a screwdriver that isn’t quite up to the task, you could end up stripping the screw, making it hard to replace the license plate if it gets stolen or damaged in an accident.

License Plate Screw Size

  • Honda license plate screw size
M6 X 1.0 X 12-20mm
  • Ford license plate screw size
1/4”-14-5/8”
  • Toyota Camry license plate screw size
1 X 0.5 X 0.5 inches
  • Hyundai license plate screw size
M6-1.0 X 16mm
  • Mazda license plate screw size
M6 X 1.0 X 25mm
  • Acura license plate screw size
M6 X 20mm
  • Audi license plate screw size
M6 X1.0 X8-16mm
  • BMW license plate screw size
M5 X 0.8 X 8-16mm
  • Chevrolet license plate screw size
#14 X 3/4”
  • Ford license plate screw size
1/4″-14-5/8”
  • General Motors license plate screw size
1/4″(#14) X 3/4″
  • Honda license plate screw size
M6 X 1.0 X 12-20mm
  • Kia license plate screw size
M6 X 1.0 X 25mm
  • Mazda license plate screw size
M6 X 1.0 X 25mm
  • Mercedes Benz license plate screw size
M6 X 1.0 X 8-16mm

M5 X 0.8 X 8-16mm

  • M5 license plate screw size
  • Nissan and Infinity plate screw size
M6 X 16mm
  • Porsche M6 license plate screw size
M6 X 1.0 X 8-16mm

Honda License Plate Screw Size

M6-1.0 x 35mm. Honda uses two different-sized screws to hold on their license plate. There is a smaller M5 screw and a larger M6 screw, so make sure you check which one your vehicle needs before heading to your local hardware store.

A standard Philips head works best to remove these screws, however, a hex key will work too if that’s all you have on hand.

Keep in mind that if you plan on removing your license plate often then it may be worth investing in some anti-corrosion spray or something similar. If not then just keep things dry when possible and they should last a while without rusting up!

Honda has many makes of vehicles and it can be hard to tell what type of car or truck yours is by just looking at it.

Ford License Plate Screw Size

Ford’s license plate screws are generally M5x0.8 or M6x1.0, which means a millimeter measurement of 5 and 8/10 or 6 and 1/10 of an inch respectively.

Remember that some manufacturers have their distinctive sizes, so it may be different than what is stated above, particularly if you’re looking to replace a Ford screw with one from another car manufacturer. It’s always best to check your owner’s manual first before purchasing any replacement parts.

If there isn’t a specific model listed in your owner’s manual, then look at an older version of your vehicle; these models will often use identical screws.

If all else fails, try checking online for Ford vehicle repair manuals to find out more about part numbers and sizes.

The average Ford motorist probably doesn’t think too much about their license plate frame as long as it does its job well: securely holding onto their registration card without rattling around on bumpy roads.

Toyota Camry License Plate Screw Size

Toyota drivers need to get a screwdriver, which is used to adjust screws on their vehicle.

A Toyota driver might be confused when purchasing screws for his license plate because there are two different types of screws that can be used.

A Toyota driver wants to know what size screw he needs to purchase. The type of license plate screw that is needed depends on what type of vehicle he has. \

Many factors such as weight, durability, and weather conditions must be considered before purchasing screws for his vehicle’s license plate.

Hyundai License Plate Screw Size

Hyundai uses license plate screws that are standard 5/16-inch. If you don’t have one, go to your local hardware store and pick up a package of screws for about $3.

You can also buy them online if you prefer.

Mazda License Plate Screw Size

1/4 x 20; Passenger Car and Light Truck (not for use with Aluminum Plates) – Max load: 6,000 lbs. – Finish Black Oxide.

This screw is typically used on license plates. The size of a license plate screw is usually denoted by its head diameter in millimeters or inches, followed by its thread pitch in millimeters or threads per inch.

Some screws are made specifically for attaching license plates to vehicles while others can be used to fasten any type of metal to metal.

Acura License Plate Screw Size

Standard plate screws are 1⁄4-inch long and 1/8-inch in diameter. The length of Acura license plate screws is designed to fit perfectly into pre-tapped holes on your vehicle’s license plate bracket, making installation a breeze.

These types of screws are sold in packages of 100 and can be found at most hardware stores for under $5.

If you need help choosing the right size for your Acura, consult with a car parts professional

Audi License Plate Screw Size

M8 x 1.25mm / M10 x 1.25mm Audi is a German automobile manufacturer founded in 1965, which primarily produces luxury vehicles under its name, as well as other prestigious automobiles under various marques.

BMW License Plate Screw Size

The size of BMW license plate screw: BMW uses screws with a thread diameter of 1/4 inch. You can buy these at most auto parts stores or online at retailers like Amazon or AutoZone. The cost is between $2 and $5 per pack depending on where you shop.

Chevrolet License Plate Screw Size

Standard Chevrolet license plate screws are 10mm, flat-head. The number of threads per inch is one thread per 3/8 of an inch.

As long as they are flat-head, they will fit any Chevrolet with pre-drilled holes (1967 and newer).

For older Chevys, you will need to drill a hole in your front bumper or bracket to mount your plate, since it requires more clearance than older cars allow.

General Motors License Plate Screw Size

5/16 x 20 in. lug bolts or license plate screws are used to mount plates on vehicles made by General Motors. GM plates are 4×8 inches, with a thread count of 10 holes per inch.

The number of threads can be determined by dividing 8 by 10, which equals 0.8. Therefore, there are 0.8 holes in each inch and therefore, one screw equals 0.8 inches long or 5/16 inches in length to accommodate all 10 holes on a GM license plate.

Honda License Plate Screw Size

M6-1.0 x 35mm. Honda uses two different-sized screws to hold on their license plate. There is a smaller M5 screw and a larger M6 screw, so make sure you check which one your vehicle needs before heading to your local hardware store.

A standard Philips head works best to remove these screws, however, a hex key will work too if that’s all you have on hand.

Keep in mind that if you plan on removing your license plate often then it may be worth investing in some anti-corrosion spray or something similar. If not then just keep things dry when possible and they should last a while without rusting up!

Honda has many makes of vehicles and it can be hard to tell what type of car or truck yours is by just looking at it.

What Sizes Are License Plate Screws

Kia License Plate Screw Size

Standard Kia license plate screws are 1⁄4 inch in diameter and 3⁄8 inch long. They’re made of steel and coated with a black phosphate to protect them from rusting.

Make sure you don’t lose your screws when you’re working on your Kia! Those license plate fasteners do not last forever, so check out our full selection of replacement license plate screws here at 1A Auto.

Mercedes Benz License Plate Screw Size

Mercedes Benz uses 5/16′′ screws to attach license plates to their cars. The threads are self-tapping, which means they cut their re being driven into place.

If you don’t have a 5/16′′ drive ratchet on hand, use a flathead screwdriver—it should fit in there just fine. However, if you do manage to strip out the hole, there is nothing that can be done about it at that point.

M5 License Plate Screw Size

M5 screws are popular for attaching license plates to vehicles. The M5 screw is 1⁄2-inch in length, with a 20 mm metric head and a 5 mm shank diameter. M5 screws have a size of 3/8 x 32tpi, which means that they have threading of #3 per inch and are threaded at 32 threads per inch.

Nissan and Infinity Plate Screw Size

The screws that hold Nissan and Infinity license plates to vehicles are nearly identical. The head-on of these screws is designed to be a little over an inch in diameter.

The heads on both screws can accommodate a flat-head screwdriver and slot-head screwdriver with equal ease.

A Philips-head screwdriver also works well with both styles of screws, but a Philips-head screwdriver can slip off of a slot-headed or flat-headed screw if you’re not careful.

Porsche M6 License Plate Screw Size

This is a common size for license plate screws on Porsche M6. Unfortunately, we do not have any information about what size it is or where you can buy these screws at.

However, you might be able to find screws that fit by taking your current screw to Home Depot or Lowes and looking around in their hardware section.

How to Remove Rusted License Plate Screw

The first step is to determine what kind of screw or bolt your license plate uses. The standard type of license plate screw is called a Phillips’s head.

You can buy them at hardware stores or auto parts stores. If you aren’t sure what size it is, you can use a magnet to find out if your screw or bolt is made of metal (which means it should be a Phillips’s head).

If it sticks to your magnet, then chances are it’s a Phillips’s head. If not, take a look at your car and see if there are any markings on your license plate holder that indicate what size screws were used.

Using your flathead screwdriver, pry off all of the plastic caps covering each hole where screws attach to your license plate bracket.

Next, insert your Phillips head screwdriver into one of those holes and gently loosen up that screw by turning it counterclockwise with your hand.

After loosening up one side, move over to the other hole and repeat steps 3-5 until both screws are removed completely.

Finally, lift your license plate holder by placing your hands underneath it and gently pulling upwards until it comes off completely.

ALSO SEE: How To Reset Car Computer Without Disconnecting Battery

What Kind of Screw Driver Do I Need To Take Off a License Plate?

Some drivers use a screwdriver with a flat-head tip while others prefer one with a pointed tip. No matter which one you choose, make sure it is small enough to fit in between your plate and its screws.

Otherwise, you may end up damaging or breaking your plate when you try to pry it off. However, be careful not to strip these screws by turning them too hard or quickly.

Although license plates are made of metal, they can bend easily if handled improperly.

What Size Are Ford License Plate Screw?

For older model cars, there are several possible sizes to use. Newer models have standard screws that are standardized by all auto manufacturers, so those who own newer Fords can easily find replacement screws in stores. It’s not uncommon for people to lose their license plate screws over time.

How Do You Put Screws on a License Plate?

There are two different types of screws that you need to put a license plate on. The first type is your license plate screw, and you will use two of these.

Place them through your frame and into the holes on your license plate, then tighten with a screwdriver so that they don’t fall out or loosen when driving around town.

You will likely need a Phillips head screwdriver for these screws.

What Size Are Audi License Plate Screw?

Typically, Audi license plate screws are 4 x 100 mm. This refers to their measurement in millimeters, and what threads they have. In total, four screws secure your license plate to your vehicle; two at the top corners of your plate and two at the bottom.

Make sure to use either a Phillips or Pozidriv screwdriver when replacing these—they’re star-shaped like Torx screws, but far more common.

What Size Are Toyota License Plate Screw?

In case you’re wondering what size is your Toyota license plate screw, there are three sizes of screws for Toyota and Lexus. They are 5/8, 7/16, and 9/16. These numbers measure from top to bottom. There are smaller ones that are used for license plates for motorcycles but they vary in measurement so it’s best to check with a reliable shop

What Size Are BMW License Plate Screw?

BMW uses three different sizes of screws on their license plates. The most common screw size they use is an 8 X 1.25MM and can be found at local hardware stores. The other two BMW license plate screws are 10 x 1MM and 10 x 1.5MM in some models that use those sizes and only in European countries like Germany for example, but not very common in other parts of Europe or North America.

What Size Are Honda License Plate Screw?

10X or 12 X #10, 1/4′′ hex head. Honda license plate screw and most other bolts are measured by either a gauge number and an outside diameter (O.D.), or a series of letter sizes and approximate metric equivalents.

For example, in both inch-pound and metric systems a #10 screw is nominally 0.1480 inches in diameter but has different diameters over its length; it’s just that smaller diameters are rare.

What Size Are Subaru License Plate Screw?

One thing most Subarus don’t come with from the factory: is a complete set of screws and mounting plates for snow chains or studded snow tires.

What Sizes Are Lexus License Plate Screw?

The size of a standard screw is measured by its diameter (the distance across its circular end) and thread pitch (the distance along its shaft). Common metric diameters range from 1mm up to 40mm; smaller diameters have finer threads, which makes it easier to work with small components but harder to apply force when tightening.

What Size Are Kia License Plate Screw?

They are different sizes and they depend on your vehicle, but most of them range from 11mm to 18mm. A screw is something made by hand or machine that consists of a shaft with a helical ridge around its surface for securing items together.

Author: Mechanic Mike Besso

Hi There, I am Mike Besso and this website is dedicated to the automotive industry. I have been a mechanic for many years and my experience includes fifteen specialization in heavy commercial work as well as private cars. I am a specialist and certified automotive mechanic (Both Heavy Commercial and Private Cars). I worked for a long time at Global Rebound Automotive companies (Toyota, TATA, BMW, Nissan, TVs, and Others ) as a Mechanic and Mechanics Supervisor. I hope to share some of my knowledge with others.

Leave a Reply

Your email address will not be published.